For Motorola Nexus 6 LCD Screen and Digitizer Assembly Replacement - Black - Grade S+
This item includes the following components:
1. LCD Display;
2. Digitizer Touch Screen;
3. Does Not Include the Front Housing, it's different with lcd assembly with front frame.
Notes: Please test the functionality of this item before installation.
Version: Without Carrier Logo
Screen Size: 5.96 inches
Resolution: 1440 x 2560 pixels, 493 ppi pixel density
Display Type: AMOLED Capacitive touchscreen, 16M colors
Protective Material: Corning Gorilla Glass 3
Compatibility: Motorola Nexus 6
? This Motorola Nexus 6 LCD assembly replacement includes the LCD Screen, Digitizer Touch Panel and Front Glass already attached.
? This Nexus 6 LCD Touch Screen does NOT include the front frame. We can also supply the Nexus 6 LCD Assembly with Frame.
? This Motorola Nexus 6 LCD Screen and Digitizer replacement is brand new and original.
How to Install / Tips:
? Please ensure to choose the right part before placing an order.
? The Motorola Nexus 6 LCD Screen and Digitizer are hermetically attached, special repairing tools are required for reassembly or disassembly.
? Make sure to handle the repair or replacement work in a dry and dust free environment without direct sunlight.
? The installation of any new part should be done by a qualified person. ETS is not responsible for any damage caused during installation.
Motorola Nexus 6 Disassembly Tutorial Guide:
1. Hair Dryer / Heat Gun;
1. Remove the Motorola Nexus 6 SIM Card Tray.
? Power off the device;
? Use an eject pin or tweezers to release the SIM card tray.
2. Remove the Motorola Nexus 6 Battery Door.
? Heat up the battery door for 2 minutes to soften the battery door adhesive;
? Insert the case opening tool and pry up the battery door.
3. Remove the Motorola Nexus 6 Rear Housing Assembly.
? Undo the 22 screws in the rear housing as shown below;
? Gently remove the rear housing assembly from the screen assembly.
4. Release the Connectors in the Rear Housing.
? Remove the gasket on the rear housing near the bottom of the phone;
? Carefully pry up the flex ribbon connector underneath;
? Remove the gasket on the rear housing near the top of the phone;
? Carefully pry up the flex ribbon connector underneath.
5. Release the Flex Cable Ribbon Extender.
? Carefully pry up the latch on the flex connector to separate it from the flex ribbon extender.
6. Remove the Motorola Nexus 6 Battery.
? Heat up the rear housing for 10 seconds to soften the battery adhesive;
(Notice: be more careful on this step as batteries might explode when overheated.)
? Pry up the battery flex connector that adhered to the rear housing;
? If you want to release the wireless charging coil as well, gently pry up the charging coil connector. However, we donâ€™t recommend performing this step as you run a high risk of damaging the charging coil and battery.
7. Release the Motorola Nexus 6 Side Keys.
? Undo the screw that locks the side key metal bracket;
? Remove the side key flex cable ribbon.
8. Remove the Motorola Nexus 6 Motherboard.
? Undo the screw and metal bracket that locks the front housing and main board;
? Pry up the LCD flex connector and digitizer connector;
? Remove the motherboard.
9. Remove the Motorola Nexus 6 Cameras.
? Pry up the rear facing camera flex connector;
? Remove the back camera;
? Pry up the front facing camera flex connector;
? Remove the front camera;
10. Remove the Motorola Nexus 6 Ear Speaker and Headphone Jack.
? Remove the front speaker.
(Notice: be careful not to scratch the flex ribbon underneath.)
? Remove the headphone jack.
(Notice: the headphone jack is strongly attached to the front housing with an adhesive.)
The Motorola Nexus 6 disassembly is now completed.
No posts found
UG21 1st Floor Qazi Electronics Center ,
Opposite State Bank Near Milli Shoes Mall Road
Powered By Digilog Electronics